unit uLandOutline;

interface

uses uConsts, SDLh, uFloat;

type TPixAr = record
              Count: Longword;
              ar: array[0..Pred(cMaxEdgePoints)] of TPoint;
              end;

procedure DrawEdge(var pa: TPixAr; value: Word);
procedure BezierizeEdge(var pa: TPixAr; Delta: hwFloat);

implementation

uses uLandGraphics, uDebug, uVariables, uLandTemplates, uLandUtils;


var Stack: record
           Count: Longword;
           points: array[0..8192] of record
                                     xl, xr, y, dir: LongInt;
                                     end
           end;


procedure Push(_xl, _xr, _y, _dir: LongInt);
begin
    if checkFails(Stack.Count <= 8192, 'FillLand: stack overflow', true) then exit;
    _y:= _y + _dir;
    if (_y < 0) or (_y >= LAND_HEIGHT) then
        exit;
    with Stack.points[Stack.Count] do
        begin
        xl:= _xl;
        xr:= _xr;
        y:= _y;
        dir:= _dir
        end;
    inc(Stack.Count)
end;

procedure Pop(var _xl, _xr, _y, _dir: LongInt);
begin
    dec(Stack.Count);
    with Stack.points[Stack.Count] do
        begin
        _xl:= xl;
        _xr:= xr;
        _y:= y;
        _dir:= dir
        end
end;

procedure DrawEdge(var pa: TPixAr; value: Word);
var i: LongInt;
begin
    i:= 0;
    with pa do
        while i < LongInt(Count) - 1 do
            if (ar[i + 1].X = NTPX) then
                inc(i, 2)
            else
                begin
                DrawLine(ar[i].x, ar[i].y, ar[i + 1].x, ar[i + 1].y, value);
                inc(i)
                end
end;


procedure Vector(p1, p2, p3: TPoint; var Vx, Vy: hwFloat);
var d1, d2, d: hwFloat;
begin
    Vx:= int2hwFloat(p1.X - p3.X);
    Vy:= int2hwFloat(p1.Y - p3.Y);

    d2:= Distance(Vx, Vy);

    if d2.QWordValue = 0 then
        begin
        Vx:= _0;
        Vy:= _0
        end
    else
        begin
        d:= DistanceI(p2.X - p1.X, p2.Y - p1.Y);
        d1:= DistanceI(p2.X - p3.X, p2.Y - p3.Y);

        if d1 < d then
            d:= d1;
        if d2 < d then
            d:= d2;

        d2:= d * _1div3 / d2;

        Vx:= Vx * d2;
        Vy:= Vy * d2
        end
end;

procedure AddLoopPoints(var pa, opa: TPixAr; StartI, EndI: LongInt; Delta: hwFloat);
var i, pi, ni: LongInt;
    NVx, NVy, PVx, PVy: hwFloat;
    x1, x2, y1, y2: LongInt;
    tsq, tcb, t, r1, r2, r3, cx1, cx2, cy1, cy2: hwFloat;
    X, Y: LongInt;
begin
    if pa.Count < cMaxEdgePoints - 2 then
        begin
        pi:= EndI;
        i:= StartI;
        ni:= Succ(StartI);
        {$HINTS OFF}
        Vector(opa.ar[pi], opa.ar[i], opa.ar[ni], NVx, NVy);
        {$HINTS ON}
        repeat
            i:= ni;
            inc(pi);
            if pi > EndI then
                pi:= StartI;
            inc(ni);
            if ni > EndI then
                ni:= StartI;
            PVx:= NVx;
            PVy:= NVy;
            Vector(opa.ar[pi], opa.ar[i], opa.ar[ni], NVx, NVy);

            x1:= opa.ar[pi].x;
            y1:= opa.ar[pi].y;
            x2:= opa.ar[i].x;
            y2:= opa.ar[i].y;

            cx1:= int2hwFloat(x1) - PVx;
            cy1:= int2hwFloat(y1) - PVy;
            cx2:= int2hwFloat(x2) + NVx;
            cy2:= int2hwFloat(y2) + NVy;
            t:= _0;
            while (t.Round = 0) and (pa.Count < cMaxEdgePoints-2) do
                begin
                tsq:= t * t;
                tcb:= tsq * t;
                r1:= (_1 - t*3 + tsq*3 - tcb);
                r2:= (     t*3 - tsq*6 + tcb*3);
                r3:= (           tsq*3 - tcb*3);
                X:= hwRound(r1 * x1 + r2 * cx1 + r3 * cx2 + tcb * x2);
                Y:= hwRound(r1 * y1 + r2 * cy1 + r3 * cy2 + tcb * y2);
                t:= t + Delta;
                pa.ar[pa.Count].x:= X;
                pa.ar[pa.Count].y:= Y;
                inc(pa.Count);
                //TryDo(pa.Count <= cMaxEdgePoints, 'Edge points overflow', true)
                end;
        until i = StartI;
        end;

    pa.ar[pa.Count].x:= opa.ar[StartI].X;
    pa.ar[pa.Count].y:= opa.ar[StartI].Y;
    inc(pa.Count)
end;

procedure BezierizeEdge(var pa: TPixAr; Delta: hwFloat);
var i, StartLoop: LongInt;
    opa: TPixAr;
begin
opa:= pa;
pa.Count:= 0;
i:= 0;
StartLoop:= 0;
while (i < LongInt(opa.Count)) and (pa.Count < cMaxEdgePoints-1) do
    if (opa.ar[i + 1].X = NTPX) then
        begin
        AddLoopPoints(pa, opa, StartLoop, i, Delta);
        inc(i, 2);
        StartLoop:= i;
        pa.ar[pa.Count].X:= NTPX;
        pa.ar[pa.Count].Y:= 0;
        inc(pa.Count);
        end else inc(i)
end;

end.